This article describes in detail how to use JXLCAM camera, including how to connect JXLCAM camera, function settings, etc.
It is suitable for all JXLCAM cameras, such as mini cameras, bulb cameras, indoor and outdoor cameras, etc.
JXLCAM APP Download
JXLCAM supports Android and iPhone, you can download it from google play or app store.
Connection Notes
- To use JXLCAM APP, please allow all permissions, otherwise you may not be able to connect to the camera. (You can turn off the unneeded permissions after setting the network mode)
- To connect JXLCAM camera, you need to turn on the GPS location of your phone, and turn on the gps location permission of JXLCAM APP, so that the app can get the wifi information of the camera. (You can turn off the permission after setting the network mode)
- If the APP can’t add camera automatically, please try to close the SIM card network.
- After connecting to the camera’s hotspot wifi, the phone prompts no network, to switch wifi, please choose not to switch.
Connect JXLCAM Camera To Wifi
Before connecting the JXLCAM camera, please connect the camera to the power supply, or in the case of a battery camera, press the on/off button to start the camera.
Networking Mode
Networked mode can use the camera remotely, as long as there is network, you can view the camera at any time.
1. Click + , select AP add camera, then enter your wifi password, click next.
Note: JXLCAM camera does not support 5G wifi, please make sure you are currently connected to 2.4G wifi.
2. Return to your phone settings, connect to the JXLCAM camera hotspot wifi, the hotspot wifi name is 17 digits of letters and numbers.
After connecting the hotspot, go back to JXLCAM APP, click Add Camera.
3. Wait for the JXLCAM camera to connect to your wifi, about 30-60 seconds or so, click Next after successful connection.
4. Click Next, and the JXLCAM camera is successfully added.
If the camera keeps showing offline, your wifi password may have been entered incorrectly, please reset the camera and reconnect.
AP Mode
JXLCAM will transmit a wifi, after connecting to the camera’s wifi you can control the camera.
AP mode can only use the camera if it is connected to the camera’s hotspot wifi, this mode is only to help networking and proximity use.
1. Connect the hotspot wifi of JXLCAM camera, then return to JXLCAM APP, APP will add camera automatically.
If the APP does not add camera automatically, please open the app permission and check the Connection Notes
Change Default Password
For security reasons, please make sure to change the default password after adding a JXLCAM camera.
The default password of the camera is: admin
In the Live Video screen, click on the Settings icon, select User, enter the original password and the new password.
1. Click Share, and save the displayed QR code.
2. Open JXLCAM APP in your new phone, click + , select Add cameras manually, then click Scan QR code to scan the QR code to add cameras.
Motion detection settings
When the JXLCAM camera detects a change in the screen, it will send a notification to your phone.
Go to the Alter screen, click Sensitive to select the detection sensitivity to start.
Recording Settings
You need to insert the memory card to record, JXLCAM camera supports 4-128G memory card. Please insert the memory card when the camera is turned off.
When the camera reads the memory card, it will automatically start recording, you can set the recording time in the TF interface, 60-300 seconds, this recording time is the video saving time, the camera will always record.
View Recording Playback
In the camera interface, click on the Play icon to view the recorded video, a colored time indicates that there is a recording at the current time.
Night Vision Settings
JXLCAM Mini camera does not support auto-sensing night vision, you need to start the night vision function manually.
Click Day/Night in the live screen to turn on/off the night vision.
JXLCAM APP Interface Description
- Add JXLCAM camera
- Camera ID number
- camera status
- Recording Playback
- local file
- camera settings
- Camera settings
- Camera power status
- sound switch
- local screenshot
- local recording
- landscape viewing
- alarm information
- horizontal flip
- vertical flip
- light switch
- night vision switch
- resolution switch
Oписание JXLCAM
Мониторинг в реальном времени, вы можете видеть дом из любого места
1. Примите захваченное изображение в реальном времени.
2. Поддержка просмотра видео в реальном времени.
3. Мобильный телефон, поддерживающий фотосъемку и сохранение видео.
4. Поддержка обмена видеоинформацией в реальном времени.
5. Напоминание об обновлениях оборудования в режиме реального времени.
Что нового в последней версии 1.5.41
Last updated on 20/08/2024
Minor bug fixes and improvements. Install or update to the newest version to check it out!
Видео и Скриншоты
Информация JXLCAM APK
Безопасная и Быстрая Загрузка APK на APKPure
APKPure позволяет легко и безопасно загружать JXLCAM APK с проверкой подписи.
Старые Версии JXLCAM
Супер Быстрая и Безопасная Загрузка через Приложение APKPure
Один клик для установки XAPK/APK файлов на Android!
Скачать APKPure
Спасибо за оценки и отзывы!
Вы уже оценили.
The JXLCAM A9 WiFi Camera User Manual is a comprehensive guide that provides users with detailed instructions on how to set up and use the camera. The manual covers both Apple iOS and Android system operations, including how to install the JXLCAM app, connect to WiFi, and switch between local and remote modes. Additionally, the manual explains how to charge the device, turn it on, and install an SD card for storing video content. The manual also includes troubleshooting tips for common issues such as poor signal strength and camera disconnection. Furthermore, the manual provides information on the FCC warning, cautionary measures, and frequently asked questions. Overall, the JXLCAM A9 WiFi Camera User Manual is an essential resource for users who want to make the most out of their camera.
JXLCAM A9 WiFi Camera User Manual
Apple IOS operations are as follows
Install the application
Download and install JXLCAM. lOS searches for “JXLCAM” download directly at the Apple App Store. For convenience, please scan the download and installation of the QR code below. Note: during installation, all permissions of the JXLCAM APP need to be allowed, otherwise the APP will not work properly. Please select app to download.
Local mode
Open the list of mobile phones WIFI, connect to B/xCCQ…, open the APP
page after success, click “AP” as shown in the figure below, and watch the video.
Note: when there is no WIFI in the environment, you can use AP mode to connect, which is valid for no more than 10m, which can achieve localized video viewing.
Remote mode
- First confirm that there is a available WIFI near the device, turn on the device, flash the blue indicator light quickly, and the device is in a state to be connected. ( Note: WIFI signals supported only in the 2.4G band)
- You cant successfully distribute the network when the power is insufficient.
- When wiring, please try to bring the device close to the router. When the nearby WIFI signal is weak, the image will be stuck if the network is not successful or the network is successful.
- Open the APP
and follow these steps:
Home page icons and button instructions
Description of icons and buttons on the video page
Storage card
If you need to store video content, you need to install an SD card. (This machine supports loop video recording)
Camera settings
NOTE:
- When the device fails to configure the network, please check whether the router and WiFi password are configured correctly (the device does not support WIFI signals in the 5.8G band). After confirming that it is correct, you can press and hold the reset button until the device indicator flashes quickly, restore the factory settings, and reconfigure network.
- When the software homepage shows that the device is offline, you can check whether the device is normally powered on, and click the refresh icon in the upper right corner to refresh.
- The initial password of the device is admin.
Appearance Guide
Charge
Please use a 500-1000mA charger to charge the equipment. When charging, the red indicator light is always on. When it is full, the red indicator light is off.Can work while charging.
Turn on the device
Press the power button to start the machine. After starting the machine, the blue indicator light flashes continuously and quickly, and the device enters the state to be connected. Note: If the blue indicator is slow flashing/always on or cannot be connected, long press the reset button for 5 seconds to reset.
Android system operation is as follows
Install APP
Download and install JXLCAM APP, Android system in Google play search download. For easy installation, easily scan the following QR code installation. Note: during installation, you need to open all permissions of the APP, otherwise the APP will not work properly.
Please select app to download
Local mode
Open your phone’s WiFi list and connect to B/xCCQ After success, open the APP page and click AP as shown below to watch the video. Note: When there is no WiFi in the environment, AP mode can be used for connection. The effective distance of this mode is no more than IOM,which can realize localized video viewing.
Remote mode
- First, confirm that there is available WIFI signal near the device, turn the device on, the blue indicator light flashes quickly, and the device enters the state to be connected. (Note: only support 2.4G band WIFI signal)
- Unable to connect successfully when power is low.
- When connecting to the network, place the device as close to the router as possible. If the nearby available WiFi signal is weak, the connection cannot be successful or the screen will be closed after successful connection.
- open the APP
and follow the steps below:
Description of icons and buttons on the home page
Description of icons and buttons on the video page
Storage card
If you need to store video content, you need to install an SD card. (This machine supports loop video recording)
Camera Setting
NOTE:
- When the device fails to configure the network, please check whether the router and WiFi password are configured correctly (the device does not support WIN signals in the 5.8G band). After confirming that it is correct, you can press and hold the reset button until the device indicator flashes quickly, restore the factory settings, and reconfigure network.
- When the software homepage shows that the device is offline, you can check whether the device is normally powered on, and click the refresh icon in the upper right corner to refresh.
- The initial password of the device is admin.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Specifications
| Product Specifications | Description |
| Compatibility | Apple iOS and Android systems |
| Installation | Download and install JXLCAM app |
| WiFi Connectivity | 2.4G band only |
| Local Mode | Connect to B/xCCQ, valid for no more than 10m |
| Remote Mode | Connect to available WiFi signal near device |
| Storage | Supports loop video recording, requires SD card installation |
| Charging Time | 90 minutes |
| Battery Life | 5 hours with power bank |
| Microphone | Built-in, sound source needs to be close to camera |
| Motion Detection | Activated with the app |
| Alerts | Can trigger email |
| Color Options | No white color available |
| Web UI | Yes |
| FCC Warning | Complies with Class B digital device limits, radiation exposure limits, and FCC Rules |
| Troubleshooting Tips | Check for poor signal strength, move camera closer to Wi-Fi router or use a Wi-Fi extender, restart phone or re-login to app |
FAQS
How long can it last if I use a powerbank if I leave it for 1 whole day
5 hours
does it has a mic jQuery111304294851029088276_1609234780381
Yes
The camera has how much battery time to have to recharge??
90 minutes
Which app does it use?
BG Bee is a network marketing platform created by Banggood that allows its users to earn money in a variety of ways. Banggood’s large product selection, technology, and support put in the hands of BG Bee users a comprehensive and functional tool to generate revenue without leaving your couch.
how can i record to sd card?
insert sd card and it should record on to sd card
Why does my camera keep disconnecting from my phone?
This may be due to poor signal strength between your phone and camera. Try moving your camera closer to your Wi-Fi router or use a Wi-Fi extender.
Do you have white color?
No
does it have a built in mic?
yes, it has built-in microphone, but the sound source needs to be close to the camera
Does it have a WEB UI? Can motion sensor trigger an email?
yes
hotspot not show on my android phone
try turning off an on again. ensure blue led lights up and look for the hotspot. then you need to use Little Stars app to see the live image
Does this camera support RTSP or ONVIF
Not sure about the first one but tested the second with an ONVIF scanner or whatever that is and nothong shows. Nevertheless, the câmera does not do what they advertise in all aspects, and mine stoped working correctly. Only direct view is posssible, no remote.
does this record sound?
yes, recording with good quality.
can it be in infra automatically without putting it on?
No
How can the motion detection and alert be activated?
with the app
My camera is offline, what should I do?
Please check whether your camera is connected to the internet. If it still can’t see, please restart your phone or re-login to the app.
Why does my camera keep disconnecting from my phone?
This may be due to poor signal strength between your phone and camera. Try moving your camera closer to your Wi-Fi router or use a Wi-Fi extender.
Views: 358
JXLCAM Smart Indoor PTZ Camera User Manual
Install APP
Use your mobile phone to scan the following two-dimensional code, select the IOS or Android version according to
the mobile phone system to install the APP, APP name: JXLCAM。
Turn on the device
Connect using the e27 bulb holder plug Equipment to 110V- 220V power supply, red indicator is Always on, the device enters the waiting state Connected, network configuration succeeded, and The red light flashes once.
Note:If the red light is always on er you cannot connect, you can press and hold the reset button to reset
Option 1: Local mode
When there is no WiFi in the environment, you can use the AP mode to connect, the effective distance of this mode does not exceed 10m, Localized monitoring and viewing can be realized.
- Each device has a unique WiFi name (device ID), and the format is unified as “ACCQ/BCCQ…….”;
- If you need to shoot and store videos, please install an SD card.
Option 2: Remote mode
If you want to use the complete functions of the device and realize remote monitoring, you need to configure the remote mode.
- First confirm that there is an available WiFi signal near the device, power on the monitoring device, the red indicator light flashes, and the device enters the standby state.
- Connect the mobile phone to the WiFi in your environment, open the software JXLCAM, and follow the steps below:
CLICK ON THE PREVIEW PAGE TO ENTER THE MONITORING INTERFACE:
REFERENCE LINK
How To SetUp JXLCAM Camera, Jxlcam is an app that works with home surveillance camera devices. JXLCAM App is developed by the JXL.Inc. JXLCAM is the app for security cameras. Now guys if you want to use JXLCAM on the PC so, You can follow some easy steps and it will be easily installed on your laptop PC.
How To SetUp JXLCAM Camera (Ultimate Manual)
This article describes in detail how to use JXLCAM camera, including how to connect JXLCAM camera, function settings, etc.
It is suitable for all JXLCAM cameras, such as mini cameras, bulb cameras, indoor and outdoor cameras, etc.
Start the JXLCAM camera
Press the power button to start the JXLCAM camera. After starting the machine, the blue indicator light flashes continuously and quickly, and the camera enters the state to be connected.
Note: If the blue indicator is slow flashing/always on or cannot be connected, long press the reset button for 5 seconds to reset.
Install JXLCAM APP
Download and install JXLCAM APP, during installation, you need to open all permissions of the APP, otherwise the APP will not work properly.
Connect the JXLCAM camera to the phone
Read Next :
- XMEYE NVR Installation Guide
- XMARTO NVR WiFi PTZ Camera System FAQ
- How to use VPN on Milesight Network Camera
Local mode
When there is no WiFi in the environment, AP mode can be used for connection. The effective distance of this mode is no more than 10M.which can realize localized video viewing.
Open your phone’s WiFi list and connect to B/xCCQ……. After success, open the APP page and click AP as shown below to watch the video.
Remote mode
- First, confirm that there is available WIFI signal near the device, turn the device on, the blue indicator light flashes quickly, and the device enters the state to be connected. (Note: only support 2.4G band WIFI signal)
- Unable to connect successfully when power is low.
- When connecting to the network, place the device as close to the router as possible. If the nearby available WiFi signal is weak, the connection cannot be successful or the screen will be closed after successful connection.
- open the APP JXLCAM and follow the steps below
1. Click ‘+’
2. Click “AP add Camera”
3. Click “…” to connect to the local 2.4G WIFI band, enter the password. and then go to the next step.
4. Click”… “to connect to the camera WIFI hotspot and add the camera
5. Click”Cancel”
6. Waiting for the connection.
7. Click”Next”
8. You can change the name or not, and then click “Next”
9. Check out the video preview on the home page
JXLCAM APP interface description
JXLCAM FOR PC
JXLCAM App is developed by the JXL.Inc. JXLCAM is the app for security cameras. Now guys if you want to use JXLCAM on the PC so, You can follow some easy steps and it will be easily installed on your laptop PC
Install JXLCAM on PC
Now Here we will going to install JXLCAM on PC, for that you have to install Bluestacks on your PC. Bluestacks is and professional android emulator to run android apps on the PC or MAC. After installing bluestacks in your PC, you can easily run any of Android apps on your PC including JXLCAM APK
So, first install Bluestacks and then you install JXLCAM in the Bluestacks emulator.
How to install the JXLCAM app on Windows and Mac
Go to the below link and download JXLCAM for PC or MAC and before that make sure to check the below minimum system requirements for installing Bluestacks on your PC to use JXLCAM.
Minimum System Requirements:
- OS: Microsoft Windows 7 and above.
- Processor: Intel or AMD Processor.
- RAM: Your PC must have at least 2GB of RAM. (Note that having 2GB or more disk space is not a substitute forRAM)
- HDD: 5GB Free Disk Space.
- You must be an Administrator on your PC.
- Up to date graphics drivers from Microsoft or the chipset vendor.
Download Bluestacks
After you install bluestacks, then you can install JXLCAM APK in Bluestacks. so follow the few steps given below to download and install JXLCAM on your MAC or PC using Bluestacks.
- Open the browser or google play to install the application
- Open your browser and type in [ https://jxlcam.com ] and download JXLCAM APK
- After JXLCAM download is complete.
- Just open the .apk file and install it as a normal .apk file
- Now, if you go to the bluestacks home screen, you will see the JXLCAM APK installed
- Just open the JXLCAM app and use it
- Now you can enjoy JXLCAM on your PC or MAC APK
FAQ
Is there any EXE or dmg software for JXLCAM?
No, to use on the computer, you can only install the APK mobile version.
Jxlcam is an app that works with home surveillance camera devices
- The monitoring of the specified device uid can be viewed only by connecting to the specified device uid
- No matter where you are, you can view the monitoring anytime, anywhere
- It supports capturing screen photos and recording videos and saving them locally
- Support monitoring camera equipment and intercom with camera equipment
- Support SD card video playback function
Android
iPhone
For PC