Satlink st 5150 инструкция на русском

SATLINK ST-5150 Digital Satellite Meter Finder

Product Information

The product is a Digital Satellite Meter used for satellite antenna
installation and setup. It comes with various accessories, including an AV
cable, car charger cable, power adaptor, carrying bag, DC 12V connect line,
BNC-Connector, and user’s manual.

Product Overview & Illustration

Product Usage Instructions

1. Before installation, please read the important safety instructions in the user’s manual.
2. Open the package and check if all the items listed below are included:

• Digital Satellite Meter
• User’s manual
• AV cable
• Car charger cable
• Power adaptor
• Carrying bag
• DC 12V connect line
• BNC-Connector

Note: Please refer to the actual configuration of your package.

1. Connect the cables to the finder and power it on.
2. Press the MENU button to display the Main Menu.
3. Use the YZA B keys to navigate up or down in the menu interface.
4. Press OK to confirm a selection.
5. Select “DVB-S2” from the menu and press OK to enter the Satellite Find Setup.
6. To select a satellite, press the A B keys to enter the satellite list. Use the YZ keys to move the cursor and press OK to select the desired satellite.
7. To select the LNB type, press the A B keys to enter the LNB TYPE menu. Use the YZ keys to move the cursor and press OK to select from the available options (C Band/Ku Band/Unicable I/Unicable II).
8. To switch the LNB frequency, press the AB keys.
9. To configure the transponder, press the AB keys to enter the TP list. Use the YZ keys to move the cursor and press OK to make changes.
10. For Unicable mode, use the A B keys to switch the IF Index or enter a specific IF Frequency using the number keys. Press A B to select A/B as Sat Position.
11. To control LNB power, press the AB keys.
12. To enable or disable beep tone, press the A B keys.
13. Once all parameters are set, press OK to start a quick search.
14. Use the YZ keys to change the transponder during the search process.

GUIDE

IMPORTANT SAFETY INSTRUCTIONS
Thank you for choosing our product. Before installation, we would like to
remind you some notes, which is very important for operating safely and
properly, as follows:

• Be sure to read this user manual before starting your operation.
• You must install the dish with correct direction and angle. If the dish is not working properly, contact your local dealer.
• When the unit is suddenly moved to a hot area from a cold area, it may cause some problems. In that case, turn off the power, and turn on again after 1-2 hours.
• Keep meter placed in clean space with sufficient ventilation.
• Do not cover the meter with or place it on a unit that emits heat.
• Clean the case by a soft cloth with a little washing liquid.
• Do not remove the cover.
• Do not let the unit exposed to extreme heat, cold or humid conditions.
• No liquids or any other materials to come inside of the unit.

UNPACKING
Open the package and make sure it includes all below items, if any missing,
please contact the reseller for replacement.

1. Digital Satellite Meter
2. User’s manual
3. AV cable
4. Car charger cable
5. Power adaptor
6. Carrying bag
7. DC 12V connect line
8. BNC-Connector

NOTE: Please refer to our actual configuration.

PRODUCT OVERVIEW& ILLUSTRATION

Картинка с сайта: manualspro.net

previous menu in sub-menu setting conditions

8| EXIT| Escape from present menu and save the settings
9| SCAN| Shortcut key for DVB-S2 menu
10| MUTE| MUTE
11| INFO| Channel information
12| AV-S| AV IN/OUT switch key
13| F1| Auxiliary function key
14| ****| Turn on/off Torch
15| AUDIO| Audio type selection / Red key
16| SAT| Shortcut key for Sat Installation menu
17| TV/R| TV/Radio switch key
18| SYS| Shortcut key for System Setting menu
19| Compass| Mechanical compass
20| NEVIGATION KEY| Volume Control or move cursor, channel or change,

confirm etc

21| 0-9| Number key to select channels or enter programming
22| RF| Connect to satellite antenna cable
—|—|—
23| ANT| Connect to antenna
24| DC OUT| DC 12V output for extern equipment
25| HDMI| HDMI output port
26| AV OUT| AV output port
27| AV IN| AV input port
28| LED| Torch
29| USB| USB port for software upgrading or multimedia playing
30| DC IN| Connect to power adaptor
31| Battery| Battery
32| Speaker| Speaker integrated

OUTLINE

• 4.3 Inch High Definition TFT LCD Screen
• Fully DVB-S/S2/T/T2/C compliant
• MPEG2, MPEG4, H.264/MPEG4 AVC, H.265/HEVC hardware decoding
• Digital meter for signal strength and quality
• Supports Auto Scan and Manual Scan
• Sound and Light Alarm for Locking Signal
• Auto Calculate Angle of AZ ,EL
• Supports DISEQC 1.0/1.1/1.2, Unicable, 0/22kHz Tone
• Speaker Integrated
• Support both AV out and AV in
• Support both HDMI out
• LNB short protect
• 7.4V/2600mAh Li‐Ion Battery Included
• Software upgrade via USB port
• Easy to carry

If you have installed and connected the cables to the finder, pressing MENU
to display the Main Menu.

• DVB-S2
• DVB-T2
• DVB-C
• Loop Search
• Angle Calculation
• Others
• Multimedia
• System Setting

Press the keys of to move the cursor up or down in the menu interface, then
use OK to confirm a selection.

DVB-S2

Select DVB-S2, then press OK into the Satellite Find Setup.

Картинка с сайта: manualspro.net

1. SATELLITE
   Press key into the satellite list. Use key to move the cursor, then press
   OK to select the satellite you want.

2. LNB TYPE
   There are 4 types you can select: C Band/Ku Band/Unicable I/Unicable II.

3. LNB FREQUENCY
   Press key to switch LNB frequency you want.

4. TRANSPONDER
   Press key into the TP list. Use key to move the cursor then press OK to
   select the TP you want.

5. FREQUENCY
   Frequency of the current transponder, input the value by using the number
   keys.

6. SYMBOL RATE
   Symbol rate of the current transponder, input the value by using the number
   keys.

7. POLARISATION
   Press key to change vertical or horizontal of polarization.

8. 22KHZ
   Press key to turn on or off 22kHz TONE Switch.

9. DISEQC MODE
   Press key to set the type of port as None/DiSEqC1.0/1.1.

10. DISEQC TYPE & INPUT
    In C/Ku Band mode:
    we can press key to set DiSEqC 1.0/1.1 as A/B port, and set Tone Burst Mode as
    NONE/Tone Burst A/B.
    In Unicable mode:
    we can press key to switch IF Index from 1 to 8, or use number key to modify
    IF Freq, and then press key to select A/B as Sat Position.

11. LNB POWER
    Press key to Switch LNB Power ON/OFF.

12. BEEP TONE
    Press key to Switch beep tone ON/OFF. If we open it, the beep of lock alarm
    will open when we enter into the search screen.

13. QUICK SEARCH
    When parameters have been set done, press OK into quick search. There will
    have some signal information displayed on the screen. Press key to change
    transponder.

    • Scan: Press the ENTER key to search the current TP.
    • Auto Scan: Press the red key to auto blind search the current satellite.

DVB-T2

Select DVB-T2, then press OK into the Scan Setup.

1. COUNTRY
   Press key to change the default country.

2. CHANNEL NO
   Press key to change the channel number.

3. FREQUENCY
   Frequency of the current channel, input the value by using the number keys.

4. BANDWIDTH
   Press key to change the bandwidth, we can select 5, 6, 7 or 8M.

5. MODE
   Press key to change the DVB standard, we have there types including T/T2/T+T2,
   you can select one you want.

6. ACTIVE ANTENNA
   Press key to switch antenna power ON/OFF.

7. LNB POWER
   Press key to change the antenna power, there are 3 types including 5V/12V/24V.

8. LCN
   Press key to switch LCN ON/OFF.

9. BEEP TONE
   Press key to Switch beep tone ON/OFF. If we open it, the beep of lock alarm
   will open when we enter into the search screen.

10. QUICK SEARCH
    When parameters have been set done, press OK into quick search. There will
    have some signal information displayed on the screen.
    

    • Scan : Press OK or red key to search current channel.
    • Auto Scan: Press green key to auto search the current channel.
    • S/Q: Press blue key to enlarge showing of the signal strength and quality.

DVB-C

Select DVB-C, then press OK into the Scan Setup.

1. COUNTRY
   Press key to change the default country.

2. CHANNEL NO.
   Press key to change the channel number.

3. FREQUENCY
   Frequency of the current channel, input the value by using the number keys.

4. STANDARD
   There are 2 types of standard you can select: J83.A/C and J83.B.

5. BEEP TONE
   Press key to switch beep tone. If we open the it, the beep of lock alarm will
   open when we enter into the search screen.

6. QUICK SEARCH
   Please refer to 3.2.10.

LOOP SEARCH

We can see 8 TP or channels when we enter into this interface, and press
OK to edit.
There are 3 modes we can choose: DVB-S2, DVB-T2 and DVB-C. Press the red key
to change.
It will finish loop search after edition, then singal strenth and quality of
each TP or channel will be displayed on the screen.

ANGLE CALCULATION

Input satellite longitude, local longitude and latitude by number key, and
device will calculate the polarization angle, azimuth and elevation on the top
of the screen.

OTHERS

• Channel Manager
• Satellite List
• Transponder List
• Motor Setting
• EPG

CHANNEL LIST

• SAT
  Press F1 key to switch different channel list.

• Lock
  Press key to select programs we want to lock, then press the red key to lock
  them.

• Del
  Press the green key to delete current channel.

• Move
  Select a channel first, then press the orange key to move to other position.

• Edit
  Press the blue key to confirm channels which need operating.

SATELLITE LIST
All the satellite will be displayed on the screen.

Картинка с сайта: manualspro.net

Press the red key to add a new satellite.

Картинка с сайта: manualspro.net

Press the green key to edit current satellite.

Press the orange key to delete current satellite. Press the blue key to scan
current satellite.

TRANSPONDER LIST
All the transponders under the current satellite will be displayed on the
screen, and press key to switch satellite.

Картинка с сайта: manualspro.net

Press the red key to add a new transponder.

Press the green key to edit current transponder.

Press the orange key to delete current transponder.
Press the blue key to scan current transponder.

MOTOR SETTING
There are 5 modes in motor setting:

• USALS
  Controling motor according to your local position, you can modify it in Angle
  Calculation.

• DiSEqC 1.2
  There are 64 position you can select to move motor.

• Set East Limit
  Move motor to east.

• Set West Limit
  Move motor to west.

• Disable Limits
  Unlimited movement.
  Press the red key to save setting.
  Press the green key to reset setting.

EPG
Press key to change program. If the current program has EPG information, it
will appear on the right side of the window. Press key to change date of the
EPG.

MULTIMEDIA
Will need to play the files in the USB and insert it into the USB port.

Select a file and press OK to play it.

SYSTEM SETTING

Картинка с сайта: manualspro.net

• Language
  Press key to change the OSD language, default is English.

• Country
  Press key to change the country.

• Aspect Ratio
  Press key to change the aspect ratio: 4:3 LB/4:3 PS/16:9/full screen.

• Video Resolution
  Press key to change the video output resolution: 480p/576p/720p/ 1080i/1080p.

• HDMI Audio
  Press key to change the digital audio output format: PCM/RAW/MUTE.

• Time Zone
  Press key to change the Time Zone.

• System Lock
  Press key to switch system lock on/off.

• PWR Unit
  Press key to change the PWR unit: dBm/dBuV/dBmV.

• Torch
  Press key to switch torch on/off.

• Back LED
  Press key to switch keyboard LED on/off.

• KeyTone
  Press key to switch key tone on/off.

• Speaker
  Press key to switch speaker on/off.

• 12V
  Press key to switch DC 12V output on/off.

• Upgrade
  Will upgrade the file into the USB, then insert the machine. Press OK to
  upgrade interface, use the direction key to select update file, and press
  OK to upgrade.
  Warning: Please don’t turn power off or pull out the USB, otherwise it
  will damage the machine’s software, and can’t boot again.

• Factory Reset
  Press OK to start factory reset.
  NOTE: if you set factory setting, all the user settings and the database
  will be reset.

• Version
  Press OK to see some information about this hardware/software.

• Save Channel – USB
  Save channel list to USB disk as default database.

• Upgrade Channel – USB
  Restore channel list from USB disk as default database.

TECHNICAL SPECIFICATION

TRANSMISSION STANDARDS

DVB-S2/S, DVBT/T2, DVB-C
SATELLITE INPUT/DEMODULATION
Connector Type| F Type
Input Frequency| 950 to 2150 MHz
Signal Input Level| – 65 to -25 dBm
Band Switch Control| 22KHz
LNB Supply| 13V/18V, IMax 400mA
Demodulation Type| QPSK,8PSK,16APSK
Symbol Rate| 2<Rs<45Mband(SCPC/MCPC)
DVB-T/T2/C INPUT/DEMODULATION
Connector Type| Female Type
Input Frequency| 48 to 862 MHz
Signal Input Level| -79.5dBm (MAX)
ANT Supply| 5V, 12V/24V Imax 100mA
Demodulation Type| QPSK,16QAM.64QAM,256QAM
LCD FEATURES
LCD Type| TFT Transmissive
Number of Dots| 480 (RGB) x 272
Active area (WxH)| 95.04×53.86 mm2
AV output interface
Connector Type| 3.5 mm jack
Video Output| CVBS
Audio Output| Stereo Audio L/R output
HDMI output connecter
Format| HDMI 1.4
AV input interface
Connector Type| 3.5 mm jack
Video Input| CVBS
Audio Input| Stereo Audio L/R input
AUDIO/VIDEO PROCESSING

Video decompression

| MPEG-2 MP@HL, MPEG-1

Decoding,MPEG‐4 ASP@L5 HD resolution,H.264 MP&HP@L4, H.265/HEVC,HW JPEG
decoding

Resolving rate| PAL-25 frame@720*576,NTSC-30

frame@720*480

—|—
Signal compatibility| Support conversion for different video formats
Video Format| 4:3,16:9,By Pan & Scan and Letter Box

conversion

Audio Decompression| MPEG-1 Layer I/II, MPEG-2 Layer I/II
Audio Output Mode| Stereo, Mono,R/L
DATA SERVICE PORT
Connector| USB
Data Protocol| USB2.0 interface
File Management System| NTFS,FAT32,FAT16
File Format| wma,mp3,mp4,avi,jpg,jpeg,bmp,img
POWER SUPPLY
Li‐Ion Battery| 7.4V/2600mAh(The machine behind

labeling shall prevail)

Adapter| OUTPUT :DC12V/1.2A, INTUPT

:100~240VAC 50/60Hz(Will

be subject to actual configuration)

Power Consumption| Max. 10W
PHYSICAL CHARACERSTICS
Size (W x D x H)| 17 x 12 x 4 (cm3)
Net Weight| 1kg

TROUBLE SHOOTING

on Run out of batteries

| Check to make sure power

on. Even on adapter

No sound or picture, but the front panel

power light is ON.

| AV IN jack insert, but no video input|

Pull out AV IN cable

No sound or picture

| The satellite dish is not pointing at the satellite.| Adjust the dish. Check
the Signal Level in the Antenna

Setup Menu

Bad picture/Blocking Error

|

No signal or weak signal

| Check the cable connections. LNB and other equipment connected between the
LNB and the meter and adjust

the dish.

The satellite dish in not

pointing at the satellite

| Adjust the dish.
Signal is too strong| Connect a signal attenuator

to the LNB input

Satellite dish is too small| Change to a larger dish
LNB noise factor too high| Change to an LNB with

lower noise factor

The LNB is faulty| Change the LNB
AV out No picture(Video)| The system is connected by SCART cable and TV is

not in AV mode.

| Check the UHF channel fixed in your system and tune the

UHF properly.

The key is not working

| Out of battery| Even on adapter
Key blocks| make sure no blocks

between the front panel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>